[email protected]

20MnB4 / 1.5525 - SteelNumber - Chemical composition

0.0008 - 0.005. New opportunities for buyers! Post free buying requirement of steel 20MnB4 (1.5525) Mechanical properties of steel 20MnB4 (1.5525) Rm - Tensile strength (MPa) 480-680. Z - Reduction in cross section on fracture (%) 55-68. Equivalent grades of steel 20MnB4 (1.5525) Warning! 20MnCr5 / 1.7147 - SteelNumber - Chemical composition Alloy special steel Chemical composition of steel 20MnCr5 (1.7147), Standards of steel 20MnCr5 (1.7147) Mechanical Properties of steel 20MnCr5 (1.7147) Equivalent grades of steel 20MnCr5 (1.7147) steel 20MnCr5 (1.7147) Tensile Strength, Elongation, Proof strength , Hardness

20MnVS6**

General Information Grade 280 variant 7260 is a micro-alloyed steel for general purposes. It is continuously cast.The chemical analysis meets the standardized grades 19MnVS6 according to EN10267 and 20MnV6 (1.5217) according to DIN mechanical properties. ALLOY DATA / 17Carbon steel; C 0.1-0.2; Mn 0.4-0.7; P 0.35 max; S 0.35 max; Si 0.15-0.4; bal Fe. Water quenched and tempered:45-65 kgf/mm**2 TS; 30 kgf/mm**2 min YS; 20 min El. A-1120 AFORA (Aceros Afora S.A.) Carbon steel; C 0.2-0.3; Mn 0.5-0.8; P 0.035 max; S 0.035 max; Si 0.15-0.4; bal Fe. Water quenched and tempered:54-74 kgf/mm**2 TS; 36 kgf/mm**2 min EN 10213 Grade G20Mn5 quenched and tempered (+QT) - Material G20Mn5, material number 1.6220 is comparable with trademark GS-21 Mn 5(1.1) acc. to SEW 685-89 rather than with trademark GS-20 Mn 5 (1.1120) acc. to DIN17182-92. It is (normalized) applicated at low temperatures up to approx. -30 °C.

Iron Base & Stainless Steel - Aimtek, Inc.

Visit us at the International Thermal Spray Conference in Quebec City, Canada, May 24-27, 2021. Please click here for more information. Visit us at Booth 2091 at MD&M West in Anaheim, CA, August 10-12, 2021. Please click here for more information. Visit us at Booth B16071 at the Fabtech International Welding Show in Chicago, September 13-16, 2021. Material Product Data Sheet Iron Chromium (Cr 20% DSMTS-0032.5 FeCr (Cr 20%) Stainless Steel Thermal Spray Wires ©2015 Oerlikon Metco 2 2 Material Information 2.1 Chemical Composition Product Nominal Composition Weight Percent (nominal) Fe Cr Ni Mn Mo C Ti Si Other (max) Metcoloy 1 Fe 18Cr 8Ni 2Mn 0.75Si 0.08C Bal. 18.0 8.0 2.0 MetalsDepot® - Buy Steel Square Tube Online!Square Steel Tube is a welded structural grade tubing that is available in either type A513 or A500 Grade B, depending on it's size and wall thickness.Either grade is ideal for all structural applications, general fabrication, manufacturing and repairs. Steel Square Tube is widely used in industrial maintenance, agricultural implements, transportation equipment, truck beds, trailers, frames, etc.

Stainless Böhler Welding - voestalpine

Stainless steel welding is a complex mix of metallurgy, chemistry, geometry and aesthetics. Knowledge and skill are essential in achieving optimum properties and surface finishes. A major element in this has been the development of covered electrodes, solid wires, flux-cored wires and fluxes for high-alloyed steels and specific applications Stainless Steels - Rolled Alloys, Inc.416 stainless steel is a free-machining martensitic stainless steel with 12-13% chromium that can be hardened by heat treatment to higher strength and hardness levels. In the annealed condition, it has better machining properties than typical austenitic stainless steels like 304 & 316. Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry. Comparison of steel grades by chemistry. EN #.

20MnCr5 - Ovako

20MnCr5 is a case-hardening steel with low carbon content but good hardenability reaching good wear resistance due to high surface hardness after hardening. The small grain size benefits in good ductility and fatigue strength. Suitable for gearboxes and axle gears. Ovako 236F is a standard variant with controlled sulphur content for consistent machining properties.